REBUILD KIT - FOLLOW / IDLE 5th Wheel Landing Gear 12 16 Bevel Gear Pin Shaft

Description: Class A Customs Listing Includes1 (One) Rebuild kit for 5th Wheel Landing Gear FOLLOW or IDLE Leg Read Entire ListingItem Details Before replacing any items please go through the checklist at bottom of listing. We are not aware if this will fit your unit, verify requirements before purchasing. FOLLOW / IDLE Leg Kit(1) Follow Drive Shaft - 4" Long x 1/2" diameter (2) Drive Shaft Bushings (1) E-Clip (1) Drive Pin (1) Spirol Pin (1) 12T bevel Gear Follow or Idle Leg is used for manual cranking and/or the leg that does not have a motor in a powered set. You will need a bar between legs to connect the Drive (motorized Leg) and Follow Leg.Drive or Lead Leg is the leg that motor will attach to. Trying to replace one leg you will need to be sure you have the same size and gear ratio to prevent legs from moving at different speeds. The hardest part of installing this kit is working in tight spaces. Your best route is to drop the leg out by unbolting the two bolts that hold the leg in. Once out it is a lot easier to work on and when your done you lift the leg back up and bolt it back in.We are not aware if this will fit your unit, verify requirements before purchasing. CAUTION & SAFETY WARNINGS Read, understand and follow all instructions before installing and using product.Failure to follow these warnings and instructions can result in property damage and/or serious bodily injury.NEVER allow anyone unfamiliar with the operating instructions to use this product.When clutch noise occurs, release the switch. Failure to do so may also destroy the clutch, in which case the entire power kit will have to be replaced. Potential damage to the trailer frame may occur if legs or power kits are operated unevenly. Front of trailer must remain horizontal. Do NOT attempt to lift or level without having both foot plates properly installed. When cranking jack or coupling trailer, secure trailer from rolling These landing gear jacks are designed for vertical loading. Excessive side forces must be avoided. Do NOT attempt to adjust the drop legs when the landing gear jacks are under load. Owner or operator must never position any part of their body under any portion of the jack or the load being supported or allow anyone else to be positioned under the load being supported. Disregard could cause property damage and/or serious bodily injury. Do NOT drop trailer off the hitch. Do NOT exceed maximum rated capacity. Make certain the drop leg safety retaining pins are fully inserted through both sides of the inner tube and the drop leg tube before using the landing gear jacks. Do NOT use these landing gear jacks to lift trailer for servicing or tire changes. Retract jack legs and drop legs fully before moving the trailer. Failure to follow these warnings and instructions can result in property damage and/or serious bodily injury. Fuses blown Circuit is overdrawn overloading the jack and it is drawing too much amperage Gear Box of the jack is damaged causing the motor to overload If your motor is making a clicking sound this is the safety clutch in the motor preventing damage to the motor. This is not the gear box. When clutch noise occurs, release the power switch. Failure to do so will result in damage to motor and possibly other system components. Check for binding Your trailer legs should be cleaned and checked for debris on a regular basis. Sand and dirt will cause legs to bind. To clean landing gear legs Extend landing legs as far as possible, clean drop tube and inner ram tube. Coat exposed surface of tubes with silicone spray lubricant. Coat inside of handle alignment tube with silicone spray lubricant. Oil shaft bushing in gear box and leg gear heads with SAE 30 oil. Lubricate gears in gear box and landing leg gear heads with extreme pressure grease. *Do NOT open motor housing as this voids warranty. Check for damage to legs Any damage to the legs such a bending or denting will cause binding. Check power to system Check that your batteries and power supplies are at full levels to prevent damage to the motor. Check wiring connections at battery. Clean terminals with a solution of baking soda and water. Cover with a thin coat of grease.Check wiring harness fuse, if blown replace with appropriate fuse. Do not exceed weight limit of landing gear system Do not use the landings legs to lift the trailer during tire changes, axle work or trailer servicing (the trailer weight will exceed the capacity of the landing legs). The landing legs are designed to stabilize a portion of the trailer’s weight. Support the front end of the trailer with structural stands rated for the GVWR of the trailer. OEM Parts No retail box, no installation instructions. Have a certified technician install all parts to prevent product damage and personal injury. For installation help and information search classAcustoms blog Payment & Shipping Information CHECK SHIP-TO ADDRESS is correct & complete, Lot #, Apartment #, Suite # Shipping if for 48 Contiguous US Only USPS MAIL (Post Office) Larger Items that don't fit in mailbox carrier may decide not to leave and you will need to arrange delivery with the carrier.Multiple Tracking Numbers eBay will only upload one tracking number per order. If you need the other tracking numbers send a message do not open a case as it is not necessary.Manufacturer Warranty Warranty does not cover install by customer or non-certified technician. No warranty, guarantee or liability is stated or implied on any product beyond the manufacturer. Class A Customs is not responsible for any damages caused from the use of this or any product we carry. FAQ's and Item Help Question: Do you have manual sets, single legs, just the motors, and etc.? Answer: Class A Customs offer a variety of landing gear kits you can view them in our online store.

Price: 39.99 USD

Location: Elkhart, Indiana

End Time: 2024-01-01T14:39:38.000Z

Shipping Cost: N/A USD